Vastu-shastra (Vol. I: Hindu Science of Architecture; Vol. II: Hindu Canons of Iconography and Painting) v1.c48.s5: III—Māna (Hastalakṣaṇa)
Vāstu-śāstra (Vol. I: Hindu Science of Architecture; Vol. II: Hindu Canons of Iconography and Painting) v1.c48.s5
- Language
- English
III—Māna (Hastalakṣaṇa)
v1.c48.s5.1
The third fundamental canon of Hindu architecture is Māna, the proportionate measurements. Vimāna is measured out Creation. Mūrtis are what when they are correctly and proportionately measured out—“प्रमाणै स्थापिता देवाः पूजार्हाश्च भवन्ति वै”. Thus adherance to the measurements is imperative in all creative activities whether it is architecture or sculpture. Unless a building is proportionately and perfectly measured out, it can not give an auspicious result. Mayamata says : मानं धात्रस्तु सम्पूर्णं जगत्सम्पूर्णता भवेत्—If the measurement of the Temple is in every way perfect, there will be perfection in the universe as well. The S. S. has also to contribute its own to this thesis. According to it any creative activity—architectural or aculptural—must be ‘Meya’ ‘complete in measures’ ‘यच्च येन भवेद् द्रव्यं मेयं तदपि कथ्यये’. Our iconographic traditions are so strict that howsoever a beautiful image is carved out, but if it lacks the correct proportions of measurements, it is deemed defecti.e and unworthy of possession. That is why it has been proclaimed by Āchāryas of the Science,—‘शास्त्रमानेन यो रम्यो स रम्यो नान्य एव . हि’’. Strict adherence to Measure or Māna has a fundamental metaphysical implication, Prof. Kramresch rightly echoes that implication in her Hindu Temple p. 43 (cf. also foot-notes): ‘Measure implies limi.s and limits mean end and death. It is by man’s own mortal frame that this knowledge of the universe is confirmed. The square, form of finality, is at the same time that of the pairs of opposites, manifestation is only through the pairs contraries. The square throne of divinity rests on the following pairs of contraries: Order and its negation (dharma and adharma); knowledge and ignorance (jañāna and ajñāna), dispassion and its opposite (vairāgy and avairāgya), and sovereignty and its negation (aiśvarya and anaiśvarya). The positive values support the throne, as its legs, in the corners, in the intermediate directions. Their negations are situated at the shafts, in the cardinal directions (cf. Isana. Pt III ch XIII. 25) and in their balance lies the perfection of the square. Its proportion embodies, and thus resolves, the finality of limitation into a symbol of perfection. Proportion and balance are the form of the subtle (sūkṣma) nature of the square, their residue is the order which belongs to the city of the Dharmarāja, who is Death and a .son of the Sun. (Similarly, the finality of architectural form houses, the life of man and is a seat of living God.) The other son is Manu, the prototype of man who gives its law to each cycle of existene.’’
v1.c48.s5.2
It may be recalled that the adherences to Māna is as old as architecture. Brahmāṇḍa-Puraṇā (Chap. • VII) gives a very apt origin of Māna, of which Aṅgula or Hasta is the standard of measurement (to be fully kept alive in the Vāstu or Śilpa texts—vide their expatiations on Measure under the caption ‘Hastalakṣaṇa’). It is stated in the Purāṇa that people at first used to live in caves, mountains, rivers, etc. They began to build houses in order to protect themselves from cold and heat (śītoṣṇa-vāraṇāta). Then they built kheṭas (towns), puras (houses), grāmas (villages) and nagaras (cities). And to measure their length, breadth, and the intermediate distance between two settlements (sanniveśa) the people instinctively (yathā-jñānam) employed their own fingers. Thence forward the aṅgulas are used as standards of measurement.
v1.c48.s5.3
The ancient sacred literature like Brāhmaṇas and Sūtras also corroborate this antiquity of the aṅgula or hasta measure as the standard of measurem nt. Thus Prādeśa frequently occurs in the Brāhmaṇas (Ait. VIII. 5; Śatapatha, 111, 5, 4, 5 etc.) as a measure of length, a span. Śūlba sūtra of Baudhyana does use a technical unit of Aratni, but explains it in terms of aṅgulas: Aratni is equal to 24 aṅgulas. We shall see more on aṅgula later, let us first introduce this subject in regard to its more important elements.
v1.c48.s5.4
The word Māna has a twofold connotation. It is general designation of Measurement as such; but more technically it is height as measurement from the foot to the top of the head (whether it is a building or an image) which is in fact nothing but height. Accordingly the line or measurement is devided in the following six kinds:
v1.c48.s5.5
1. Māna, (also called Ayāma, Āyata, Dīrgha); 2. Pramāṇa; 3. Parimāṇa (also called Vistāra, Tāra, Striti, Vistriti, Vistrita, Vyāsa, Visārita, Tata, Viṣkamba, Viśāla); 4. Lamba-māna (Sūtra, unmita); 5. Unmāna (Bahala, Ghana, Miti, Uchchhrāya, Tuṅga, Unnata, Udaya, Utsedha, Ucca, Niṣkrama, Niṣkṛti, Nirgama, Nirgati, Udgama) and 6. Upamāna (Nīvra, Vivara, Antara).
v1.c48.s5.6
We have already seen the meaning of māna under Māna. Pramāṇa is the measurement of breadth (Vistrita). Parimāṇa is the measurement of width or circumference (paritah). Lamba-māna is the measurement along the plumb lines or the lines drawn perpendicularly through different parts of the body, Māna, or the measurement of height being determined by the surface of the body. Unmāna is the measurement of thickness (nimna) or diameter. And Upamāna is the measurement of interspace (antara), such as the distance between the two feet of an image; this measurement is apparently taken from one plumb line to another. These terms are more sculptural than architectural.
v1.c48.s5.7
There is yet another system called Ādimāna primary measurement, which is but the comparative measuement and chiefly useful in sculpture and iconography. It is also divided and subdivided in nine kinds—vide Encyllopadia of Hindu architecture p. 418-19. Similarly as aṅgula was the chief measure in Architecture, so Tāla in Sculpture. The details of the Tālamāna may not be reproduced here (cf. my Vāstuśāstra Vol. 11). Like Tālamāna in sculpture, it is called Gaṇyamāna in architecture which is the comparative height of the component members of an architectural structure.
v1.c48.s5.8
Five proportions of the height, as compared with the breadth of an architectural object, are given under technical terms, namely, Śāntika, Pauṣṭika, Jayada, Sārva-kāmika or Dhanada, and Adbhuta'. These terms are very interesting from the stand-point of their implied aesthecity or durability of the building. Dr. Acharya says: 'The t chnical names of the proportions of the height are significant. The first one is called ‘śāntika’ or peaceful. In this proportion the height is equal to the breadth (M., XXXV line 22); and this is aesthetically a graceful proportion. The second one is called ‘Pauṣṭika’ which might be rendered as strong, eminent, rich, complete, or perfect. In this proprotion the height is 1¼ of the breadth (ibid., line 22); and this would give the building good stability. The third one is called ‘Jayada’ or joy-giving. In this proporation the heigh is 1½ of the breadth (ibid, line 22), and this gives a pleasant appearance to the building. The fourth one has two names, ‘sarva-kāmika, or good in every way, and ‘dhanada’ or wealth-giving. In this proportion the height is 1¾ of the breadth (ibid., line 23)’ and according to the literal meaning of the term ‘sārvakāmika’ this would make the building strong as well as beautiful. The fifth or last one is called ‘adbhuta’ or marvellous. In this proportion the height is twice the breadth (ibid,, line 22); and this would givea wonderful loftiness and gorgeous look to the building.”
v1.c48.s5.9
With this general introduction let us treat this subject in more details from the evidences of the principal texts like the Mānasāra and the Samarāṅgaṇasūtradhāra. Let us first begin with that culled from the Mānasāra.
v1.c48.s5.10
Aṅgula, the standard of measurement, is a measure of about three-fouths of an inch as the hasta may be taken for easy computation at exactly 18 inches which gives ¾ inch as the value of the aṅgula. Three kinds of aṅgulas are: Uttama, the longest, madhyama, the intermediate and kaniṣṭha, the smallest, and the Suprabhedāgama has an interesting list of synonyms of number of aṅgulas and the following tabulation from Acharya,s Encyclopaedia may be purviewed:
v1.c48.s5.11
One aṅgula is called bindu, mokṣa.
v1.c48.s5.12
Two aṅgulas are called kalā (elsewhere it is the name of one aṅgula), kolaka, padma, akṣi, aśvinī.
v1.c48.s5.13
Three ” ” ” rudrākṣi, agni, guṇa, śūla (and) Vidyā.
v1.c48.s5.14
Four ” ” ” yoga (and) bhāga, Veda, and turīya.
v1.c48.s5.15
Five ,, ,, ,, rudrānana, indriya, bhūta, and vāṇa. Six ,, ,, ,, karman, aṅga, ayana, and rasa. Seven ,, ,, ,, pātāla, muni, dhātu and abdhi. Eight ,, ,, ,, vasu, lokeśa, and mūrti. Nine ,, ,, ,, dvāra, sūtra, graha, and śakti. Ten ,, ,, ,, dik, nāḍī, āyudha, and prādurbhāva. Twenty ,, ,, ,, trishu (and) vishku. Thirty ,, ,, ,, gati. Forty ,, ,, ,, trijagat (?) Fifty ,, ,, ,, śakvarī. Sixty ,, ,, ,, atiśakvarī. Seventy ,, ,, ,, yaṣṭī. Eighty ,, ,, ,, atyaṣṭi. Ninety ,, ,, ,, dhṛti. Hundred ,, ,, ,, atidhṛti.
v1.c48.s5.16
Hasta, the bigger standard is constituted by the aṅgulas. Hence avoiding the details of Aṅgula as are stated in the Mānsāra, let us concentrate on the evidence of the S. S.
v1.c48.s5.17
Proportionate measurements being the very essence of the architectural planning, the author of the S. S. devotes a separate chapter to this. The unit of the measurement in architecture is Hasta. It is defined as the instrument of all Vāstus, the only basis of all the actions (pertaining of course to the constructions, etc.); the only medium through which all the proportions of measurements can be ascertained. It is of three kinds—superior, ordinary and inferior.
v1.c48.s5.18
The units of absolute measurements being :—
v1.c48.s5.19
| 8 Reṇus | = 1 | Bālāgra |
| 8 Bālāgras | = 1 | Liksā |
| 8 Liksās | = 1 | Yūkā |
| 8 Yūkās | = 1 | Yava-madhya |
| 8 Yava-madhyas | = 1 | Aṅgula called Prāśaya |
| 7 ,, | = 1 | ,, called Sādhāraṇa |
| 6 ,, | = 1 | ,, called Mātrāśaya |
| 24 Aṅgulas | = 1 | Hasta i.e. the modern foot. |
v1.c48.s5.20
This Hasta consists of 8 parts (Parvas), the middle half should be indicated and the remaining portion to be divided into divisions of Aṅgulas. All the Aṅgulas should be indicated by lines, only three of which are to be decorated with flowers and others left undecorated.
v1.c48.s5.21
After this, certain trees of which this rod should be made are enumerated together with the trees unfit to be employed in its construction. The Parva-rekhās (the lines) of this yard-stick are said to have the presiding deities beginning from the centre, the place of Brahmā.
v1.c48.s5.22
Directions are given with regard to the use of these different kinds of yard-sticks:--
v1.c48.s5.23
The superior yard stick called Prāśaya is to be employed in the measurement of Prāsāda, temples, Veśma, the large buildings, drenches, moats, gates, Rathyā, Sabhā, etc. The middle type called Sādhāraṇa is employed in measuring talocchrāyas, mūlapādas, subterranean water reservoirs, dolās, rock-cut temples and suraṅgas etc., while the inferior one called Mātrāśaya is fit to measure the weapons, the rod of the bow, conveyances, cots and couches, wells, vāpīs, elephants, horses, araghaṭṭekṣu-yantras, chatra, dhvaja etc. etc.
v1.c48.s5.24
Other units of measurements are now described :—
v1.c48.s5.25
| 1 Aṅgula | =1 Mātrā | 12 Aṅgulas make one Vitasti | | |
| 2 ,, | =1 Kalā | 14 ,, | make one Pāda | |
| 3 ,, | =1 Parva | 21 ,, | make one Ratni | |
| 4 ,, | =1 Muṣṭi | 24 ,, | make one Aratni | |
| 5 ,, | =1 Tala | 42 ,, | make one Kiṣku | |
| 6 ,, | =1 Hasta | 84 ,, | make one Vyāma or puruṣa | |
| 7 ,, | = 1 Diṣṭi | | | |
| 8 ,, | = 1 Tūṇi | 96 ,, | make one Cāpa or | Nādī- |
| 9 ,, | = 1 Prādeśa | | | yuga |
| 10 ,, | = 1 Śayatāla | 106 ,, | make one Daṇḍa | |
| 11 ,, | = 1 Gokarṇa | 30 Dhanuṣas make one Nalva | | |
| | | 1000 ,, make one Krośa | | |
| | | 2000 ,, make one Gavyūti | | |
| | | 4 Gavyūtis make one Yojana | | |
v1.c48.s5.26
Another interesting item of the description (of Arithmetic) is the 20 numbers.
v1.c48.s5.27
| 1. One | 1 | 11. Kharva | 10000000000 |
| 2. Ten | 10 | 12. Nikharva | 100000000000 |
| 3. Hundred | 100 | 13. Śaṅkha | 1000000000000 |
| 4. Thousand | 1000 | 14. Padma | 10000000000000 |
| 5. Ayuta | 10000 | 15. Amburāśi | 100000000000000 |
| 6. Nivuta | 100000 | 16. Madhya | 1000000000000000 |
| 7. Prayuta | 1000000 | 17. Antya | 10000000000000000 |
| 8. Arbuda | 10000000 | 18. Para | 100000000000000000 |
| 9. Nyarbuda | 100000000 | 19. Apara | 1000000000000000000 |
| 10. Bṛnda | 1000000000 | 20. Parārdha | 10000000000000000000 |
v1.c48.s5.28
In the end are given the details of ten units—the time numbers (Kāla-saṅkhyā) :—
v1.c48.s5.29
| 1 Eye-twinkling | ... | ... | ... | 1 Nimeṣa |
| 15 Nimeṣas | ... | ... | ... | Kāṣṭhā |
| 30 Kāṣṭhās | ... | ... | ... | Kalā |
| 30 Kalās ... | ... | ... | ... | Muhūrta |
| 30 Muhūrtas | ... | | ... | Day and night |
| 15 Ahorātras i.e. days and nights... | | | ... | Pakṣa |
| 2 Pakṣas ... | ... | ... | ... | One month |
| 2 Māsas ... | ... | ... | ... | One Ṛtu |
| 3 Ṛtus ... | ... | ... | ... | One Ayana |
| 2 Ayanas | ... | ... | ... | One year |
Cites (9)
- Īśānaśivagurudevapaddhati — Īśānaśivagurudeva, Sanskrit
- Aitareyabrāhmaṇa — Mahidāsa Aitareya, Sanskrit
- Śatapathabrāhmaṇa — Yājñavalkya & Śāṇḍilya (Vedic teacher), Sanskrit
- Brahmāṇḍapurāṇa — Vyāsa, Sanskrit
- Samarāṅgaṇasūtradhāra — Bhoja, Sanskrit
- Mānasāra — Sanskrit
- Suprabhedāgama — Sanskrit
- Mayamata — Maya, Sanskrit
- Baudhāyanaśulbasūtra — Baudhāyana, Sanskrit